Contact Us
TEL: +86-755-21006895
Mob: +8618923838718
E-mail: sales01@ottima-tech.com
Address: 4th Floor, Building 1, Puhua Technology Park, Gongyeyuan Road, Da Lang, LongHua New District, Shenzhen, China
36 Volt LED Driver

36 Volt LED Driver

80W 36V constant voltage led driver
Triac dimmable LED Driver
IP67

Specifications

Model

OTM-TD80-PH12

OTM-TD80-PH24

Certificates

FCC UL cUL

FCC UL cUL Class 2

Output

DC Voltage

12V

24V

Rated Current

6.66A

3.33A

Rated Power

80W

Voltage Tolerance

±0.5V

Voltage Regulation

±0.5%

Load Regulation

±1%
±1%

Input

Voltage Range

100-277VAC

Frequency Range

47-63Hz

Power Factor(Typ.)@ full load

0.98@120VAC  0.95@277VAC

THD(Typ.)@ full load

<20%

Efficiency(Typ.)@ full load

82%
79%

AC Current(Max.)

1.3A@100VAC

Inrush Current (Typ.)

20A, 50%, 1.6ms

Leakage current

<0.50mA

Protection

Short Circuit

shut down o/p voltage, re-power on to recover after fault condition is removed

Over Loading

≤120% constant current limiting, auto-recovery

Over temperature

100℃±10℃ shut down o/p voltage, automatically recover after cooling.

Environment

Working TEMP.

-40~+60℃ (see below derating curve)

Working Humidity

20~90%RH, non-condensing

Storage TEMP. Humidity

-40~+80℃,10~95%RH

TEMP .coefficient

±0.03%/℃(0~50℃)

Vibration

10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes

 

Safety& EMC

Safety standards

UL8750+UL1310

Withstand voltage

I/P-O/P:1.88KVac

Isolation resistance

I/P-O/P:100MΩ/500VDC/25℃/70%RH

EMC EMISSION

FCC Part 15 B

others

Net. Weight

1.05Kg

Size

230*70*43mm (L*W*H)

packing

10PCS/CTN
385*335*200mm 20PCS/CTN

Notes

1. All parameters if NOT specially mentioned are measured at 120VAC input , rated load and 25℃of ambient temperature.
2. To extend the driver's using life ,please reduce the loading at lower input voltage.


■ Mechanical Specification



※ Input Rubber wire 3*18AWG Black and White to be connected to AC L and N ,Green wire go ground, 

※Output Rubber wire, 2*16AWG Red to LED Positive side (+) , Black  to LED Negative side (-). 


■Dimming Operation

※The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection a phase/triac dimmer.

※Usually matching with Forward phase , leading edge , Magnetic low voltage, triac dimmers, or Reverse phase, trailing edge ,Electric low voltage Dimmers.

※Please try to use dimmers with power at least 1.5 times as the output power of the driver.


■ Instruction:

1)This driver should be installed by qualified and professional person;

2)Please make sure the driver is installed with adequate ventilation around it to allow for heat dissipation.

3)Ensure that wiring is correct before test in order to avoid light and power supply damage;

4)If driver Cannot work normally, don’t maintain privately; Have any question, please contact us 




Hot Tags: 36 volt LED driver, China, mAnufacturers, factory, in stock
Inquiry